COPLATE®️ Ref. CBZwi1-
20F2
COPLATE®️ Ref. CBZwi1-20F2 for trainer: Zwift Hub One-
JetBlack VOLT ™
Short execution.The top and bottom plate are made of coated birch plywood 12mm.
Including mounting kit with 2 bolts (no velcro) for securing the Zwift Hub One on the Coplate® and included standard EPS front wheel riser*, H =5cm (ref. 14036).
Due to the small tilting angle of the front wheel, it is not absolutely necessary to use a front wheel rocker table.
Price € 171,90: excl. freight, excl. VAT and excl. Tax (outside EU)
No stock: expected delivery from 18 December 2023
Freight: NL from € 5,60 , Belgium, Germany, Denmark, France, Luxembourg, UK, Austria, Sweden and Spain: from € 12,50Due to the small tilting angle of the front wheel, it is not necessary for a front wheel booster to tilt along with the tilting plate.
JetBlack VOLT ™
Short execution.The top and bottom plate are made of coated birch plywood 12mm.
Including mounting kit with 2 bolts (no velcro) for securing the Zwift Hub One on the Coplate® and included standard EPS front wheel riser*, H =5cm (ref. 14036).
Due to the small tilting angle of the front wheel, it is not absolutely necessary to use a front wheel rocker table.
Price € 171,90: excl. freight, excl. VAT and excl. Tax (outside EU)
No stock: expected delivery from 18 December 2023
Freight: NL from € 5,60 , Belgium, Germany, Denmark, France, Luxembourg, UK, Austria, Sweden and Spain: from € 12,50Due to the small tilting angle of the front wheel, it is not necessary for a front wheel booster to tilt along with the tilting plate.
|
Every COPLATE® is supplied with:
- Standard EPS FRONTWHEEL RISER *, (ref. 14036) Height: =5cm. Note: When ordering the rocking table kit Ref. CB-RT2, the above-mentioned front wheel riser is not supplied with a COPLATE® - PRESSURE GAUGE, Ref. 14029 - MINI AIR PUMP, Ref. 14028 - MANUAL, in Dutch and English * Important information: While using a rocker plate, we recommend (see below): the front wheel riser ref. CB-VT or a rocking table kit Ref. CB-RT2, a trainer mat and the step ref. CB-0S |
 (delivery without shown Tacx frontwheel support)
*Standard FRONTWHEEL RISER, Ref. 14036-2020, 2525, 2036 Material: XPS hard foam. Height: 5cm Eliminates almost the height difference 8cm of the COPLATE®  Minipump ref. 14028
MINI AIR PUMP, Ref. 14028 for inflating the air suspension.  Pressure gauge ref. 14029
PRESSURE GAUGE, Ref. 14029 with deflating function , Case: S.S. Ø 40 mm, Range: black 0-1 bar / red 0-15 psi. |
COPLATE®️ Accessories
Ref. CB-RT2
|
FRONT WHEEL ROCKER TABLE KIT Ref. CB-RT2*
The front wheel rocker table brings the frontwheel at the same height with the COPLATE®️. Can be used in combination with COPLATE®️for use with road bike. Two special supports give much more stability, specially during sprinting and climbing. The front wheel rocker table is connected to the COPLATE®️ by a steel tube, two bolts and clamps*. The top- and the bottom plate are connected to each other by means of two rocking rubbers, same ones as in the COPLATE®️. Made of black coated birch plywood 12mm. *Important information: If the 2 mounting holes (Ø6.5 mm) are missing in an older COPLATE®️, they must be drilled into the top plate of the COPLATE®️ according to the manual of the CB-RT2. Dimensions (excl. tube): 41x29x8 cm. (LxWxH). Price: € 63,90 excl. freight, excl. VAT and excl. Tax (outside EU) Delivery: from stock |
Ref. CB-0S
STEP Ref. CB-0S
When using the rocker plate with height 9 cm, this step is very helpful in getting safe and easy up and off your bike. Made of black coated birch plywood 12mm and four chrome plated steel legs.
Dimensions: 27x27x12 cm (LxWxH)
Price: € 38,65 excl. freight, excl. VAT and excl. Tax (outside EU)
Delivery time: from stock.
When using the rocker plate with height 9 cm, this step is very helpful in getting safe and easy up and off your bike. Made of black coated birch plywood 12mm and four chrome plated steel legs.
Dimensions: 27x27x12 cm (LxWxH)
Price: € 38,65 excl. freight, excl. VAT and excl. Tax (outside EU)
Delivery time: from stock.
Ref. CB-VT
FRONT WHEEL RISER 'DE LUXE’ Ref. CB-VT
When using the rocker plate with height 9 cm this "DE LUXE" riser is recommended instead of the standard supplied EPS foam front wheel riser with a height of 5cm. Made of black coated birch plywood 12mm and 4 chrome plated steel legs.
Dimensions: 41x29x12 cm (LxWxH).
Price: € 40,65 excl. freight, excl. VAT and excl. Tax (outside EU)
Delivery: from stock
FRONT WHEEL RISER 'DE LUXE’ Ref. CB-VT
When using the rocker plate with height 9 cm this "DE LUXE" riser is recommended instead of the standard supplied EPS foam front wheel riser with a height of 5cm. Made of black coated birch plywood 12mm and 4 chrome plated steel legs.
Dimensions: 41x29x12 cm (LxWxH).
Price: € 40,65 excl. freight, excl. VAT and excl. Tax (outside EU)
Delivery: from stock